Interfacing Nokia 3510i and 5110 LCD with PIC Microcontroller

Recently, I started to regain some interest in embedded systems, and started to experiment with PIC micro-controllers. After some successful attempts with standard character LCDs using the HD44780 controllers, I decided to get some Nokia LCD modules from eBay to explore.

The 2 LCD modules I purchased are for the 3510i and 5110 models. Both have built-in controllers which use Serial Peripheral Interface (SPI). The following are the pinout for my modules, notice that pin assignments may vary slightly.

LCD Pinout

Nokia 5110

Nokia 3510i

The only difference here is pin #5 which is used as data/command selection for the 5110, and unused for the 3510i.

Voltage Difference: 5.5v vs 3V

Both LCDs are designed to work with 3.3V, but due to an internal voltage clamp 5V can be used for SCLK, SDATA, REST, D/C and CS as long as a current limiting resistor (around 10k) is connected in series for each line. 3.3V should still be applied to VCC and the LED supply. I have tried using voltage dividers, which did not work, perhaps due to the LCD varying internal resistance and current consumption.

With the above connections, we can only write to the LCD but can’t read back the LCD response because 3.3v is not high enough to register as logic ‘1’ in the PIC. Luckily, reading from the LCD is not required for basic operations; all that is needed is sufficient delay after each operation to make sure the LCD is ready for next command.

I have chosen the PIC16f88 simply because it’s available in my junk box. For simplicity, I have decided to use bit-banging to send data, and not the PIC built-in SPI module. Although this usually means complicated code and lower throughput, it does not matter as all I wanted is to get the LCD to display something useful.

LCD Memory Map

The 5110 LCD is monochrome, uses the PCD8544 controller and has a resolution of 48 rows × 84 columns. Each 8 pixels on a single column consumes a single byte on the LCD memory map. It takes 504 bytes to fill the entire LCD.

The 3510i LCD has 97×66 resolution and can operate in either 256 or 4096 colors. Since there seems to be little difference between 256 and 4096 colors due to the small resolution, I have chosen 256 colors for simplicity. Each pixel on the LCD is represented by a single byte and filling the entire LCD takes 6402 bytes in 256-color (8-bit) mode.

Sample Code: Displaying Test Patterns

The following code shows how to display all black pixels on the Nokia 5110 LCD. Notice that LCD initialization code is not shown.

void lcd_5110_clear()
{
    for (int i=0; i<84;i++)
    {
        unsigned char row;
        for (row=0;row<6;row++)
        {
            //all black pixels
            char data = 0xFF;
            
            lcd_5110_send(0x40 + row,0); //Y address
            lcd_5110_send(0x80 + i,0);   //X address
            
            //write to display memory
            lcd_5110_send(data,1);
        }
    }
}

The following code shows how to display a selected color on the 3510i LCD:

void addset(unsigned char x1,unsigned char y1,unsigned char x2,unsigned char y2)
{
    send(0x2a,0);  //column address set
    send(x1, 1);
    send(x2, 1);
    send(0x2B, 0); //page address set
    send(y1, 1);
    send(y2, 1);
    send(0x2C,0 ); //memory write
}

void LCD_Clear(unsigned int value,unsigned char Color)
{
    unsigned char x, y;
    addset(0,0,97,66);
    for(y = 0; y < 67; y ++)
    {
        for(x = 0; x < 98; x ++)
        {
            send(Color, 1);
        }
    }
}

Displaying Text and Graphics

Up until now, you can only display test patterns on the LCDs. The use of a bitmap font (and extra code) is required if you want to display any useful text. I have chosen a 8×12 font for the 3510i LCD, and a 5×8 font for the 5110 LCD. The font, together with any graphics to be displayed, will be stored in a 24C64 (8Kbytes) I2C EEPROM. To program the EEPROM, I use the I2C version of the PonnyProg programmer. Notice that this may not work on newer PCs where the available current from the serial port is limited and will never work with a USB-to-serial converter. In my experiment, I made a stupid mistake of adding a LED via a 470 ohm resistor to show activity during programming. This results in data corruption and verification errors after programming due to excessive current consumption. Changing the resistor to 2k worked fine, although the LED is much dimmer.

With the EEPROM to store font and graphics, the 5110 LCD could now display text and some monochrome bitmap:

The 3510i LCD could do a much better job. 

Notice that the serial port connector is for debugging purposes only.

The entire source code is attached here. The contents of the EEPROM is included with the source code and named eeprom.bin.

See Also

• ST7735 1.8″ 128×160 color LCD
• ST7920 128×64 graphical LCD
• Other LCD modules that I have interfaced