|
Installed the new motherboard and set about connecting all the cables from the case. I have never before had a motherboard or a case that had a firewire connection on it. So I read the manual and have come away from it more confused than before.
The manual is talking about 1394a and provides the following table.
TPA+ 1 2 TPA-
GND 3 4 GND
TPB+ 5 6 TPB-
12V 7 8 12V
Empty 9 0 GND
It also states that if you connect things up wrong you will do great damage. Don't want to do that so immediately thought I should ask strangers on the Internet again.
The cabling from the case has the TPA + and - and the TPB + and -, no GND and also has a VP and VG. I can obviously connect up the first four, but where do the VP and VG go and what problems will I have if I don't have any GND connected?
Michael Martin
Australia
"I controlled my laughter and simple said "No,I am very busy,so I can't write any code for you". The moment they heard this all the smiling face turned into a sad looking face and one of them farted. So I had to leave the place as soon as possible."
- Mr.Prakash One Fine Saturday. 24/04/2004
moved on Wednesday, July 30, 2008 10:44 PM
|
|
|
|
|
you do have a GND, even though it's no identified so.
I hope some will confirm, but i think VP is "voltage positive" (+12V), and VG is the Ground (GND)...
ps: if it's not, i don't replace motherboards 
|
|
|
|
|
It seems to me that VP = Voltage Positive and VG = Voltage Ground
Steve
|
|
|
|
|
I agree with the above VP = 12v and VG = ground.
Pins 3,4 and 0 will (or should) be connected to each other on the board as should 7 and 8 so connect VG to 3, 4 or 0 and VP to 7 or 8. You could verify if you have a multimeter (make sure there's no power to the board and set to measure resistance)?
DaveBTW, in software, hope and pray is not a viable strategy. (Luc Pattyn)
|
|
|
|
|
Hi friends, I found that if using SCM to load a driver dynamically there would be a system event log as follows:
The XXX.sys service was successfully sent a start control.
How can I load the driver without this event log? 
Thanks.
|
|
|
|
|
what are you trying to do ? hacking by driver 
Vikas Amin
UNITED STATES STEEL CORPORATION
My First Article on CP" Virtual Serial Port "[^]
modified on Thursday, July 24, 2008 5:33 PM
|
|
|
|
|
I find another program which uses driver as well but I never see the event log for the driver when it is loaded. I just feel strange about it and I just want how to hide the event log.
|
|
|
|
|
Hi, I have a problem with my memory upgrade on my computer. I have lost the manual of my motherboard, so I could not know what is the maximum size of the memory that I need to upgrade in my computer.
From here I would like to know are there any tool that I could use to scan my computer hardware and it could let me know the maximum memory that my mainboard is support and the maximum memory that my mainboard support for each slot?
Thank in advance!!!
|
|
|
|
|
crucial has a scanner to do that. www.crucial.com[^]
Today's lesson is brought to you by the word "niggardly". Remember kids, don't attribute to racism what can be explained by Scandinavian language roots.
-- Robert Royall
|
|
|
|
|
Thank you very much. I already found it and but it is available only on the internet. My computer at home could not connect to an internet. Are there any version of this software that could scan locally without accessing to an internet? Thank in advance
|
|
|
|
|
I'm a little confused,
Is a (i.e processor) cache just another name for the stack? Or are they different?
A wiki definition search of cache seemed to match my understanding of the stack (i.e temporarily stores data that is likely to be used again).
Cheers,
|
|
|
|
|
Hi Mark,
cache and stack are completely different things.
A stack is a data structure intended to keep historic information, things get pushed on it, later on
popped from it, in reverse order.
Microprocessors typically contain the required logic in hardware to have an execution stack,
where each call of a subroutine/function/method (CALL, JSR, or whatever the assembly instruction is called)
automatically pushes the "program counter" (and possibly a bit more) onto the stack, and when
returning from the subroutine (RETURN, RTS, ... instruction) automatically pops the same information
from stack and restores it in the appropriate registers, so normal program flow can continue
where it left of before.
A cache is a data structure intended to keep a copy of existing information at hand, typically
to boost performance. Caches operate on a statistical basis; if they contain what is needed,
then all is good; if not, data is loaded from elsewhere, probably main memory.
Modern processors have an on-chip "level 1" cache (typically two, one for
data, one for code), and a "level 2" cache and sometimes the control logic for a "level 3" cache.
Each level has different sizes and speeds, level 1 being the smallest but fastest.
A typical example would be a CPU running at say 1 GHz, requiring 1 cycle to access one of its
registers, 2 cycles to read from its level 1 cache, 4 cycles to read from its level 2 cache,
and hundreds of cycles to read from main memory (main memory works at microsecond speeds, not
nanoseconds).
Conclusion: a stack is a logical entity, it holds specific information that is necessary for
correct execution; a cache holds a copy, and is used to speed up things.
BTW: extra stacks can be implemented by software (e.g. each thread in a system needs its own
stack); extra caches can also be implemented by software (e.g. results of a long computation may
be stored in a cache, so if they happen to be required again later on they might be found there).
|
|
|
|
|
Thanks Luc,
I'd feel sorry for anyone who had to compete with you for a job... Is there anything at all about computers or math you don't know? 
|
|
|
|
|
Hi Mark,
I started as an electronics engineer, so I do know the internals of a processor.
In fact I designed some myself, very simple ones; on paper, not for real.
This hardware knowledge helps me a lot in understanding how a system is operating,
or failing for that matter.
While I read a lot about software, it is hard if not impossible to keep up.
I am aware there is much more to know than is humanly possible
(IMO Leonardo Da Vinci was the last human to know all technical stuff humanity knew at the time)
So I am struggling with the latest stuff, say LINQ, XAML, Lambda, and what have you.
However, I have an inquisitive mind; I don't like the feeling of hearing
about something without really knowing what it is. Hence, I am reading a lot, and
rather busy on the Internet...
|
|
|
|
|
Hi,
I'm trying to find out if this is possible, and if so how to do it. From a machine running XP or Vista, as I understand it, when you send something to print, Windows/the print drivers render the file into a format the printer can read and understand (a spool file?). This file is sent to the printer then the local copy is deleted. I believe this file is held briefly in the 'C:\WINDOWS\system32\spool\PRINTERS' folder, which is effectively the shared print queue folder. for all printers on that machine.
My question is whether you can capture this 'raw' spooler data (I've managed to copy and paste to capture the files that appear in the spool folder, but you have to be fast!), and crucially, once you've captured it, can you then somehow send it to print again?
I have a feeling this is more complicated than I think. Presumably there are different formats of spooler data etc? Is there a utility that can do the printing/viewing of captured files?
|
|
|
|
|
|
hi
please help
my PC restarts itself
it just started out from no where
it worked fine yesterday but today the problem occured
when i tried the BLUE SCREEN ....it shows:
STOP:0x0000008E(0xC0000005,0x8054A51A,0xB8BD2B90,0x00000000)
i searched about this but nothing helps
i didnt install any new programs .....as i told u ....i did nothing
somebody please guide me through this
i appriciate anykind of help
thank u all
|
|
|
|
|
Did this happen once, or it occurs repeatedly. Wat is the primary purpose of ur PC, coding? gaming etc
Need more details.
|
|
|
|
|
actually...it occurs repeatedly
now i cant open my PC
and another thing:
i used to go to the SAFE MODE and it works fine
but now the same thing happend
so now icant open it
****its ahome PC******
simple
now what should i do
|
|
|
|
|
Since u cant get into windows, the best thing is to repair ur windows using the OS cd, instead of where it asks new installation the second time, select the partition, eg C:, and select REPAIR.
This way if there are any system files corrupted, they wud be restored and u wont loose any data or settings.
Then u can re-install ur motherboard and other peripheral drivers as well.
U'l hav a fresh system then.
|
|
|
|
|
STOP 8E is KMODE_EXCEPTION_NOT_HANDLED - an exception occurred in kernel-mode code. The first parameter is the exception code. Here it's STATUS_ACCESS_VIOLATION (0xC0000005), which means that the code tried to read from or write to an address that either didn't have anything mapped there, or that the address was marked read-only.
In this case we know it was a read that failed, as the fourth parameter is 0 (it will be 1 for a write). The other two parameters are the address of the instruction and the address it was trying to read from but I can't remember which way round they are.
Most likely it's a bug in a device driver that requires a fairly uncommon set of circumstances to make it happen. The driver at fault should have been listed on the blue screen.
You could see if there are any updated drivers for the device, but this isn't guaranteed to help.
DoEvents: Generating unexpected recursion since 1991
|
|
|
|
|
just take this as advice, just shut down your PC, remove the RAM(Random Access Memory) clean the RAM slot with the help of air blower and reconnect it & then check, I hope it should help.
Regards
|
|
|
|
|
Hi,
I'v been thru lots of articles related to hardware changes but couldnt find one specifically for this topic.
OS/Platform : win XP / .NET C# v2.0
im unable to get the relevant Windows Native APIs, though i'v tried in advapi.dll as well.
one way is to use the WndProc(ref message) method but this works with windows form where you can intercept the WM_CHANGE... signals.
Need a breakthru with services, as i work with smartcard Readers and Contact/Contactless/RFID tech.
-ck
|
|
|
|
|
Are you trying to monitor if a smart card has been inserted/or RFID card swiped?
or are you looking to compare hardware profiles to check if a device is present?
|
|
|
|
|
Using the service, im trying to detect if an appropriate reader has been connected so that i can launch the corresponding application.
|
|
|
|
General 
News 
Suggestion 
Question 
Bug 
Answer 
Joke 
Praise 
Rant 
Admin 
Submit an article or tip
