|
You'll have to excuse me if I don't click on that link. Judging by the URL, it has absolutely nothing to do with USB issues.
|
|
|
|
|
|
Yeah, I saw that right after I hit Post.
|
|
|
|
|
Hi Gurus,
There has been a requirement to use Gemalto PC PIN Pad device in unsecured mode, Secure Pin Entry (SPE) not active. We have been trying our best to search online for any hint but unfortunately no luck yet. We can't contact Gemalto support because of no formal purchase of device yet (we are in R&D/evaluation phase) as Gemalto is requesting device information formally.
Any hint would be greatly appreciated.
Best Regards,
Asif
Do
Read();
Research();
Experiment();
UnTil You Inspire!
|
|
|
|
|
_Asif_ wrote: Any hint would be greatly appreciated.
Gemalto are the only people who will have the knowledge to help you.
|
|
|
|
|
There's always a company salesman in the middle you need to deal with if it's not on Amazon, etc. That's their job.
It was only in wine that he laid down no limit for himself, but he did not allow himself to be confused by it.
― Confucian Analects: Rules of Confucius about his food
|
|
|
|
|
hello
i need the same as you. We need to be able to use it for loyalty purpose with.
Do you succeed to use it in an unsecure way to be able to get the pin back to a computer ?
thanks
JJ
|
|
|
|
|
Some PCIe devices cannot read more than 4 GB of address space without an additional driver or modified driver. In such cases, what limits how much memory they can read? Is it the memory controller? Is it the firmware of the PCIe device? Or is it something else? I don't think it is because of the device driver itself because PCIe devices can read or write to RAM without a driver. Someone said it is a 32-bit vs 64-bit issue but I do not understand why PCIe device can only address 32-bit.
|
|
|
|
|
I have purchased an ST8000NM0075 as this drive is compatible with my SAN system. However, this drive shipped with E001 firmware on it and I need it to run the LE OEM firmware from lenovo for this drive to work. I have been unable to find a way to flash the LE firmware onto a drive with E firmware. Is there anything I can do to make this work?
|
|
|
|
|
You would be much better served asking this on Seagate's forums than anywhere else.
|
|
|
|
|
Hello,
I am looking for ideas or even solutions to access the video or image stream of BOA SPOT cameras from Teledyne DALSA directly for further image processing. Teledyne has a SDK which unfortunately does no support this series of cameras. Only their pre-built software solution gives access but cant be integrated in other programs.
So far I didn't find any SDK or solution which does not rely on theis Sapera SDK (which doesn't support BOA)
forging iron and new ideas
|
|
|
|
|
Contact Teledyne and ask them to help you.
|
|
|
|
|
Been there, done that. They want to sell (more expensive) cameras which are supported by their SDK, not the other way round. Yet we cant just tell our customers "sorry, got to buy new cameras because the old one is the same but it has no official support" 
forging iron and new ideas
|
|
|
|
|
Good day pals! Please I have been curious about this since I studied Computer Science. How can I build a hardware and control this hardware via my vb.net, c# or c++ application designed by me?
I know this question is vast but I only need guidelines on how to go about it probably the right keywords to use in searching please
|
|
|
|
|
Depends on the interfaces provided by your hardware.
forging iron and new ideas
|
|
|
|
|
15 Great Arduino Projects for Beginners
The Master said, 'Am I indeed possessed of knowledge? I am not knowing. But if a mean person, who appears quite empty-like, ask anything of me, I set it forth from one end to the other, and exhaust it.'
― Confucian Analects
|
|
|
|
|
Sorry, I don't want to use existing board. I want to build my own hardware from scratch. I can build the hardware cos I have knowledge but don't know how to communicate the hardware with software I have designed in any of the language
|
|
|
|
|
All microcontroller or CPU chip manufacturers have C compilers and libraries to communicate with the chips. There will be a lot of example code on their websites.
|
|
|
|
|
I have a PC that randomly shuts off after being on for more than 10 minutes.
A couple of times, I've been on the BIOS setup screen, and the hardware monitor has shown that the 12 volt supply drops below 11 volts to around 10.3 volts.
About two seconds after the voltage drop, the PC shuts off.
Is that enough of a variance that I can be confident it's the power supply causing it to shut off?
The difficult we do right away...
...the impossible takes slightly longer.
|
|
|
|
|
My first thought would be a bad power supply. If you're brave enough to open the case of the supply and not shock yourself on a charged cap, look for bulging capacitors in it.
It's also possible your motherboard may have a bad VRM stage or bad caps there too. Eletrolytic caps on a motherboard are not common any more. They tended to last about 5 years whereas the polymer caps that replaced them last for about 20+ years.
|
|
|
|
|
I'm going to replace the power supply, so we'll see what happens. 
The difficult we do right away...
...the impossible takes slightly longer.
|
|
|
|
|
It's almost a 15% loss of voltage, which is definitively significant enough to screw things up.
"Five fruits and vegetables a day? What a joke!
Personally, after the third watermelon, I'm full."
|
|
|
|
|
Thank you, I feel better about springing for a new power supply now. 
The difficult we do right away...
...the impossible takes slightly longer.
|
|
|
|
|
I used [STM32F407] to write a network port program, and the connection with the host computer can sometimes be connected, sometimes not connected.
Connected normally with the F7 board. So it is a software problem. Please help me find a master
Any suggestion
Thank you!
Chenoa
|
|
|
|
|
I want two atmega32s to communicate in a 1000-foot range, so I decided to use a serial line. I know that rs232 is not a good way to communicate in this wide range, so I decided to use RS485 which is a balanced pair. To do this, I want to use a MAX485 chip like this.
What the program basically does is that an atmega sends "Paresh" on the serial port, another atmega receives it, and if it does receive "Paresh" then it issues a strcmp which emits "Mathur". If the first atmega receives "Mathur", it sends paresh again and continues to loop.
After several cycles of debugging, I received a strange string. what should I do? Why can't I use RS485 communication for my design purposes. Long-distance communication through the serial port. 
|
|
|
|
General 
News 
Suggestion 
Question 
Bug 
Answer 
Joke 
Praise 
Rant 
Admin 
Submit an article or tip
